!#1: Buying 600 Watt Low Voltage Transformer: 2011

!: Promotion LiteFuze LR-5000 5000 Watt Heavy Duty Voltage Regulator w/ Voltage Converter Transformer - Step Up/Down 110/120/220/240V (Free Euro Plug) - Patented Universal Output Sockets purchase

Brand : LiteFuze
Rate :

Price :
Post Date : Oct 19, 2011 19:48:09
Usually ships in 1-2 business days

Up to 5000 Watt Maximum Capacity Heavy-Duty Voltage Regulator Heavy duty for continuous use On/Off Power Switch LED Indicator for Power Source Single phase Dual Voltage Step Up or Step Down functionality Input: 110V/120V or 220V/230V/240V (Single Phase) Output 110V/120V or 220V/230V/240V (Single Phase) Input Selection in the rear of the converter Dimensions: 12"x11.5"x7" * Weight: 34 lbs. Five outlets for output in the front - 2 sockets - Universal outlet (220/240v single phase) - 3 sockets - Grounded USA (110/120v) Fuse protected with Built in Circuit Breaker NOTE: We recommend to use a Voltage Converter / Transformer that's max watts is at least 50% higher than your appliance. Some appliances such as Power tools, Motors, Laser printers and TVs require 2-3 times more watts at start up than the printed rating. We do not recommend voltage converters to use with coffee makers, hair dryers, microwave ovens and other heat producing appliances. US 220V products are two-phase 220V products and are not designed for use with this item.

Best Prices Mouse Trap Glue Comparison Gardenia Passion Perfume Learn Deer Baby Bedding

!: Testing a Transformer - How To Accurately Test A Transformer

There is two types of transformers in the market- linear transformer and switch mode power transformer. The transformers found is different. Sometimes it is just referred as ac transformer. Linear transformer mostly used in radio, project kits, Vcd and etc while switch mode transformer can be found in Monitor, Tv, Fax and so on.

A transformer consists of two or more coils wound on the same core. For power transformers, the core material is usually iron. For a radio-frequency transformer, the core material is usually ferrite or air. The basic asset of a transformer is to convert Ac voltage. A transformer cannot convert direct current voltage. A step down transformer has a lower Ac yield voltage at its secondary winding than the Ac input voltage to its traditional winding. Conversely, a step up transformer has a higher secondary than traditional voltage. The transformer laminations or coating of shellac, enamel or varnish is to insulate adjacent turns from shorts in the middle of winding. I will not go too details about how transformer work and transformer calculation as you can read more details from most electrical and electronic transformers books.

How to test transformers: Transformer failures are relatively rare in most electronic equipment, compared with other Components. If too much current goes through a coil or winding, the winding heats up and can either open up completely, or the insulation in the middle of turns of wire can break down, causing the coil to be partly or fully shorted.

Just like a coil, you can check continuity of any traditional or secondary transformer winding. The actual value of Dc resistance you read is rather meaningless, but at least you will know either a winding is open. Checking linear transformer is quite right forward. Apply the ac voltage to the traditional winding and expect yield voltage at the secondary side. No or low yield voltage means the transformer winding has open or shorted winding. Look for any evidence of overheating, such as darkened or blackened areas or a burnt smell.

About how to test a power transformer-it is a little bit complicated. You cannot apply ac voltage to the equipment and expect the desire yield at the secondary side without associate to load otherwise over voltage will happen (because you have removed all the secondary load) and will blow the power section which consist of power fet, pwm ic and etc. Switch mode power supply are designed to run with load while linear transformer can be test without load.

The best way to test a switch mode power transformer is first take off it from the board. Check only the traditional winding as secondary winding failures are exceedingly rare. How do we know which one is the traditional winding? Trace from the big filter cap the certain pin to see where the circuit goes. It will go to one of the pin of the transformer. Then look for the power fet middle pin which is the Drain and it will lead to another pin of the transformer. This two pins is the traditional winding of the transformer. Checking the resistance of the traditional winding only can impart either it is open but it cannot check if it has developed a shorted winding. Only by using a ringer test you will know if it shorted or not. A shorted turn in the traditional winding can cause the power section to blow.

The cheapest ringer tester that i came across is Dick Smith Lopt Meter or flyback tester. Just associate the probes to the traditional winding and the ensue are instantly seen from the Led bar graph. 4-8 bar recount a good winding, 1-2 bar recount partial short and if the led goes off means there is a heavy short in the winding. Also checking the transformer it can be use to check B+ Coil, horizontal yoke coil and flyback traditional winding and ballast (choke).

The costly ringer tester is from sencore equipment. Sencore Lc102 and Lc103C Also checking capacitor it also have the capability to check all kind of winding. either it is a low voltage transformer, high voltage transformer, current transformer, pulse transformer, galvanic transformer, convention transformer this equipment will be able to check and test it.

If you do not wish to spend on this tester you may use a light bulb to check it. take off one of the traditional winding pin and associate a 60 watt light bulb. One end to the circuit while the other to the transformer pin. If the bulb light and didn't goes off hypothesize a shorted winding and if the light goes off, the winding is ok.

Transformer heal is not easy and it wish a good skill to do it. Most of the transformer repairer favorite to rewind bigger winding such as fan, car alternator and starter. Switch mode power transformer is a little bit difficult to rewind because of the small size and low price.